Our Products:    Top quality new Satellite Receivers with factory service in the USA!            Deals from http://www.mpeg2fta.com

To order you must call us at 859/356-9666 We want to talk to you to make sure you are getting what you want. In the satellite business since 1985

               Credit Cards  Accepted 

Email Us     

HOME

                                 MPEG2 free to air  Receivers   Add $79 for a system (most cases)

                                           System includes receiver, lnbf and Antenna, plus shipping

Note,  the following is not well organized so be sure to scroll all the way to the bottom to see all products.

New C-Ku feed for big dish, scroll down

24" actuator with clamp for satellite dish
In Stock $39.99  better order before they sell out, again.  That is an amazing price for a decent actuator.

Move that big dish, control with your IRD such as 4DTV or analog receiver, OR a V Box V.  V Box V controls the actuator with its own remote control or interfaces with many FTA receivers such a the Traxis  3500

SPECIFICATIONS  

     . Standard duty for mesh type dishes

       .moves or travels approx. 24 inches

  • Superior Anti-rust process
  • Epoxy power coated steel tube and high grade plated hardware
  • Excellent water proofing
  • 3 drain holes
  • Super Reed Sensor
  • Ruthenium plated contacts ensures longer sensor life
  • Hermetically sealed in a clean atmosphere to eliminate effects of dust and corrosion
  • Zero oxidation
  • Advanced design prevents sticking, binding or wearing
  • Plastic impregnated for easy installation.

TECHNICAL SPECIFICATION

Model Rating Load@25V Maximum load@25v Power Supply Voltage REED Sensor Currency
TA-24 Actuator 200Kgs 360Kgs DC24-36 ﹤=10mA

exact style may vary

18" actuator with clamp for satellite dish        $38.99 

SPECIFICATIONS

   standard duty for smaller mesh           dishes, say approx. 6 foot

  • Superior Anti-rust process
  • Epoxy power coated steel tube and high grade plated hardware
  • Excellent water proofing
  • 3 drain holes
  • Super Reed Sensor
  • Ruthenium plated contacts ensures longer sensor life
  • Hermetically sealed in a clean atmosphere to eliminate effects of dust and corrosion
  • Zero oxidation
  • Advanced design prevents sticking, binding or wearing
  • Plastic impregnated for easy installation.

TECHNICAL SPECIFICATION

exact style may vary

Model Rating Load@25V Maximum load@25v Power Supply Voltage REED Sensor Currency
TA-18 Actuator 200Kgs 360Kgs DC24-36 ﹤=10mA
New, DBS 4000, usually no installer needed. Light on LNBf turns green when on satellite.  Click here for installation details Receiver $119, LNBf $39.  Add dish to package $59, Dish alone $79

HDMI and Audio Video Cable component out for high quality picture (no Channel 3 out)

OUR BEST SELLER

Traxis DBS 3500 with Blindsearch

Traxis DBS 3500   $99.99  we can preprogram for one station or one satellite. We do it all the time for TV stations and  serious users
* Blind Search
* Fully MPEG2 DVB Compliant
* Free converting between PAL source and NTSC display
* User programmable various satellite and transponder information
* Stores up to 100 satellites/4,000 channels
* EPG: Display of title and information up to 16 days events
* Easy and fast software upgrade through RS232 port
* Multi LNBF control by DiSEqC 1.0/1.2 and 0/22KHz switching
* SCPC/MCPC receivable from C and Ku band satellites
* Multi-language: English, German, French, Spanish, Italian, Polish, Portuguese, Turkish

 

Traxis  DBS5500 CI  Takes Cams for smart cards (not for Dish Network)  More Information   Call for price and availability. Nagra (not Dish) cams available.  Irdeto Call
Cams for Traxis 5500 ,  and other receivers that take cams., they fit in a PCMCIA slot that some receivers have.  Very limited supply of Irdeto cams,  and Nagra (not dishnetwork) cams.  PCMCIA slot is like the ones in some laptop computers.  Call - Call - Call. 

call to check for availability

These devices insert into a pcmcia like slot to take a smart card  Nagra  $109,  Irdeto call
   920 $129 used  Gi or Motorola  digital for big dish 4DTV     
Traxis DBS3800 Rack Mount with Blind Search.  Can't find that feed,,,  Blind Search will!!!

Why blind search on a rack mount?  Just ask the guys at the TV station that spent 3 days looking for a feed and it turned out that the "Engineers" gave them the wrong specs.  We found the feed in 5 min with a Traxis blind search receiver!!!!

Comes with remote control the can be disabled with switch on back of receiver.  You can stack multiple receivers and program one receiver at a time. On screen graphics.  Best of both worlds, traditional rack mount ,AND set top box Compare to other brands costing thousands. $189 that is not a misprint

* Blind Search
* Fully MPEG2, DVB Compatible
* Free converting PAL to NTSC
* User programmable
* Stores up to 100 satellites/4,000 channels
* EPG title and information up to 16 days events
* Remote controlled with switch on receiver
* RS-232 for easy software upgrades
* Multi LNB controlled by DiSEqC 1.0/1.2
* 0/22 KHz switching
* SCPC/MCPC receivable from C/Ku band
* Multi-language: English, German, French, Spanish, Italian, Polish, Portuguese, Turkish
* and more

See the specs      See the Manual

Videocipher Modules

4 DTV sidecar, and 920s      call

Great for laptops 

This is the latest external satellite receiver that hooks up to your computer.  We just brought a limited supply of these units home from the distributor, supply is very limited. What makes it work so well is that it uses the processor in your computer.    

Get the details at http://www.matchboxpro.com    only $89

 
  • Mini Size
  • Gorgeous Appearance
  • USB 2.0 High Speed Transmission
  • Watch & Record Satellite TV & Radio
  • Multi-Media Files Support
  • Third Party Software Support
  • IP Data Transmission
  • Operation System
    • Windows XP
    • Windows 2000
    • Windows Vista
  • Comes with Blaze HDTV Player Registered Software
    US$49.95 value at no extra charge
DiSEqC switches   2x1 and 4x1, switches between 2 and 4 inputs Warning  unplug receiver from AC when installing ANY DiSEqC switch to avoid power surge.  2X1 $9.99, 4X1  9.99, also available 8X1  and 4X1 with weather cover
Other switches, see Home page for pictures 0 / 12 volt ab $25

1 port passing High Freq splitters $5

These switches can be used with special splitters to interface with analog or 4DTV receive

Winegard $69, dish  0.76 meters, plus freight

-------------------------------------------

We now have the 2005 Hotdish 0.76 meter  $59, Big enough for almost all uses, plus shipping. Hardened steel, will not go out of shape in sun like other inferior dishes assembly instructions

 

$29  

Make your receiver into a system for only $59 more, includes Dish and lnbf. $69 without receiver. Installation kits. available. Antennas are drop shipped from Ga. or Mich. warehouse. shipping charge may apply when picked up in Cincinnati

VERY IMPORTANT Our dishes are made with hardened steel,  the tend to spring back and hold their shape, not like the dishes that one church broadcaster sent out then when they didn't work instructed installers to look across them then straighten them by bending them.  We have serviced these dishes and have bent them back.  Our Dishes are made in Europe and Iowa and are made of good steel.  Don't buy Junk.

These adaptors are common in Europe.  I saw a number of dishes in London with 2 lnbfs. New, add second lnb for nearby satellite,  DirecTV and  T5 or ? in this week, adjustable $23.99, yes the picture is backward  for t5 and DBS.Fits Hotdish,  Winegard requires hole to be drilled. Initial tests show that one bracket is capable of an orbital spread of 4 to about 14 degrees  See home page for more detail. May not be exactly as pictured.

Home Page for more lots more information and great links to our help pages

Need a remote control,  check our surplus page  remotes for current products usually $18.99                   

We are one of the largest dealers of Coship rack mount commercial receivers, with product in TV stations, commercial downlink facilities, cable headends, and network production facilities.  We have customers from the Bermuda to Hawaii.  More Info

Order number, 859/356-9666                                        ACCESSORIES

V Box 6VBox 6

Our newest V Box.   Compatible with DiSEqC 1.0 /1.2 Receiver or Any Receiver.  Compatible with any Actuator or H-H Mount.  3 Digit LED Display.  99 Satellite Positions.  Fine-tune EAST / WEST Buttons.  Comes with Remote Control.  Overload Protection ( Auto-recovery ).  Anti-Noise Design.  Short circuit and over load protection.  Auto turn-off function.  Re-synchronize Function.  Includes a 22 key remote control. 

*Note: Available in 110vac 60Hz or 220vac 50Hz.

Move your big dish, h to h, actuator arm with your FTA receiver, or remote control included.  This will do the job those Uniden 300 controllers that we sold all that we could get our hands on and more!$59

Specification:

 

input Voltage 110 VAC 60 Hz or 220 VAC 50 Hz
13/18 VDC (F Type via Coaxial Cable)
Output Voltage 13/18 VDC (F Type / According to input)
36 VDC via motor cable
Maximum Current 2.2A
Power Consumption Standby: 5W
Maximum: 70W
Position Memories 99 / 8 / 4
Protocol DiSEqC 1.2/1.0
Remote Control IR
Operating Temperature 5°C to 40°C (41°F to 104°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Dimensions (WxHxD) 225x160x75mm³ (Net) 275x205x83mm³ (Gross)
Weight 1.6 Kg (Net) 1.7 Kg (Gross)

 

$12.99 switch and bracket,  $6,99 Holder only  (closeout) Present stock only
4 DSS bracket

Allows you to mount 4 DSS type LNBFs on your DSS dish

aligns to 119°, 110°, 101°, 91°
Includes bolts and spacer.
Need more satellites from your DSS dish?  Use this custom bracket to mount up to 4 DSS LNBFs on your dish.  
Progressive Scan receiver -improves picture,,, Info    see info that is all we know, we have not tested this product but have received good reports on it.  It is Not an off air tuner

Call closeout

Inline Amplifier, Goes in you coax line to amplify signals over long runs of coax.  450 - 2100 MHz.  Heavy duty cast case gain 14 - 20 db (plastic cap on right is removed before installation)  $9.99 call
NEW!  Puts all of your VHF and many cable channels on UHF.  Ch 3 becomes Ch 37,  Ch 4 becomes Ch 38.  This allows user with way 4 satellite receivers to combine signals and send them out on home cable system with combiners and /or reverse splitters.  $24
ONLY $59 (THIS IS THE REAL ONE)  Setting up motor using USALS, easy way SG 2100,  it moves a Ku Winegard or other dish. Requires DiSEqC 1.2 capable Receiver or Digibox controller .  Enjoy programming from several satellites with one dish.

alternate installation method; http://dmsiusa.com/documents/SG2100%20easy%20manual.pdf

Picture shows drive with Hotdish bracket installed, bolt goes all the way through the inverted mount pole. dish attaches at right 

Specification:
bullet  For Dish up to 1.2M
SG2100
Antenna Diameter 1.2M Max. (33 lbs / 15 KG)
Azimuth Angle 70˚EAST ~ 70˚WEST ( 140˚ ) Adjustable
Elevation Angle 25˚~75˚
Input / Output Voltage 13 / 18 VDC
Power Consumption

50 mA (Standby mode) 
200 mA (Normal)
350 mA (Max.)

Rotation Speed 1.9˚ / sec ( at 13V) ; 2.5 ˚/ sec ( at 18V)
Satellite Positions 60
Connector F Type
Command Protocol DiSEqC 1.2
Resynchronize Function YES
Goto Position 0 Function YES
Goto X Function YES
Positioning Sensor High Resolution Hall Effect Sensor
EAST / WEST Limit Adjustable Hardware and Programmable Software
Manual Button EAST / WEST
Indicating LED YES
color status indication
Green On Power On; Standby Mode
Orange Blink Receiving DiSEqC 1.2 Commands/ Reset Mode
Orange On Error Message: Over Current / Hardware Limit
Tube size for antenna 55x160mm
Stand size 35~65mm

  New Product      97 deg West Telstar 5 or G-19 and 101 deg West  on the same dish.

JSC-MB4-2 Mono Block LNBFJSC-MB4-2 Ku Mono Block Universal LNBF  $24.99 single lot
Have you always wanted to get Galaxy 19 and AMC4 on the same dish?  Now you can get Ku satellites that are spaced at 4 degrees with this Mono Block LNBF.  

HDTV ApprovedDigital Ready, HDTV approved, latest technology provides the best possible performance.  Receives two satellites at four degree spacing.  The DiSEqC switch is built in allowing you to deliver both signals down one coax without adding move devices in line.  0.3dB noise figure, high stability and high gain insures that you get the best possible picture.  Only JSC LNBFs have the ability to give you the best reception
Just in, the new 621-2d is the latest, standard C Band and Universal Ku.  No Internal swithc, run 2 coax cables or use a DiSEqC swith.  Lower price $49 

We also have the 621 which is standard Ku and standard 10750 Ku.  In stock $49

 

 Use a V-Box to move your big dish.  

 

 

 

How to realign probe due to over tightening  f-connecter on end of feed

We have big dishes in stock  7.5 foot, 10', 12 foot mesh,  plus 180 solid one piece and 240 cm 4 piece solid by Fortec.  Most dishes must be shipped by Motor Carrier.  Call for Price.  also 6' Mesh that can be shipped FedEx Ground.

Used dishes available for pickup in our Cincinnati warehouse, 7.5' 6', 10'. More details on our surplus page.  Special  6 foot mesh Dish made to be  place on ONE satellite,  new $169  several in stock.  Also new 6 foot polar mount, takes actuator  $179   UPS  / FedEx ground shipable.

Solid dishes now available with polar mount, special order

 

 Mini T 710-18T
18", 60
0 lb Load,    6'-7.5' Suggested mesh dish size

call or see our own brand at top of page

18 Maxi has been discontinued

Maxi 810-24K
24",
1000 lb Load, 32 Pulse, 10' Suggested mesh dish size

ask for price

Venture 819B24CK Ball Screw
w/Accordion Boot, , 24" Ball Screw, 1500 lb load, 40 Pulse, 16' Suggested mesh dish size

Maxi 818-36K
36",
1000 lb load, 32 Pulse, 16' Suggested mesh dish size

call

 Superjack not pictured VBRL3036 XLBall Ball  $239  no boot

Venture 819B36CK Ball Screw
36" Ball Screw, 1500 lb load, 40 Pulse, 16' Suggested mesh dish size

call

 Special Order, must be prepaid no return

Maxi MA818-52CK
52", 1000 lb load, 32 Pulse, 16' Suggested mesh dish size

call

We Sell Venture Actuators,  high quality.  Venture is a Dayton Ohio company.

 

Other brands available.  Prices and availability subject to change

Call because prices are going up

 

Prime or Offset Dish

Only $19.99 for this 0.3 db lnbf

Offset is like  our Hotdish, Prime is like a 10 footer with feed is the middle

Just in, the BSC321SP!  This standard Ku lnbf  works equally well on either a offset dish or a prime focus dish. Specs apply to latest version.

It is a 0.3 DB standard 10750 lnbf, that is probably the best that you can get.  All dealers and experimenters should have at least one in stock.  BSC is a new technology, tops for performance and reliability.    Price $19.99

    $12.95

 

It appears to be for 3 leg feed supports and most dishes use 4, we are checking on this one.

C-band LNBs from DMS International ASC 211  digital ready c -Band LNBs    3.7 to 4.2 mhz  $29

Use with big dish.  A must for upgrading to digital.  Old LNBs may work fine on analog but may drift and not be able to deliver a digital MPEG 2 fta signal

Dual output allows you to use 2 receivers at the same time and receive  the channels on a standard fta receiver from both the DBS frequency circular such as NASA which my be in the clear, as well as standard Ku. linear birds.  This LNBf is best used with a 0.76 meter dish.  lo 10750, not for use with a E* or D* receiver.  Special, sales final, no return Just in $23.95  D922

We have not used one yet so click here for details

Important Note: Replace the F-Fitting Replace the F Fitting!  I have seen an f fitting that looks only slightly tarnished cause tiling or even kill a signal on an MPEG2fta receiver even though the 4DTV or analog system works fine!!!0

 

lWe use these high stability dependable lnbs for commercial downlinks.

ASC 511  High Stability Ku lnb -  0.5 db noise figure  Commercial Quality $$49 

500 K stability500 KHz Hi Stability Ku LNB.  55dB gain.  Covers 11.7 GHz to 12.2 GHz using a LO frequency of 10750 MHz.  Excellent pricing for high stability.  Use for Digital and / or analog.

JSC321S Standard Ku Digital Ready LNBF

11.7 to 12.2 GHz standard US frequency

10750 MHz LO frequency

0.3dB Noise Figure

Outputs 950-1450 MHz

40mm throat

Single output

New Latest 0.3 DB  standard LO 10750, $19.99

We also have Universal LNBf.s several varieties

These are single port.  We also have dual and 4 port supporting two and four receivers working independently   Dual  $23.00 and Quad $34.99    

These are for most 0.7 m 31 inch as well as 0.9 and 1.2 meter dishes.

Supports 4 receivers       BSC 324-2  universal 

 

10./7-11.7 GHZ+ 11.7-12.2 GHZ

0.3 db typ.

$32.95  each 

BSC  421      13 deg  C Band  $29.99

C-Band  voltage switched LNBF, style may vary.  Use the 14, 18 volt switching capability of your new receiver and your big C-Band dish.  13 degree K, with circular polarity removable slab   $69We also have ADL and Chaparral C Band feedhornss , Chaparral Ku mini feeds, with servo polarity $49Also hard to find Chap. Tri Band feed  K-Ku linear circular $189  C-Ku-S

picture not available, however it has 1 port in, two out and 2 lugs to attach wires to receiver.

Some use straight wires some use rca plugs, not supplied

0 / 12 volt switch a/b switch between input ports  $18.99
   Just in,  PCT Genesys II 4 way splitters  5 - 1000Mhz  These are the good ones.  No power passing  $2.49  call for quantity pricing  
2-Way 5-2300MHz Commercial Grade Satellite Splitter.$3.99 Splitters,  High frequency ONE port passing. This allows the user to split into a line coming to say a present analog or 4DTV receiver and with switches use one of our new MPEG2 receivers without having to change wires or manual switches
22 K switch   $9.99
One port in for off air and another port in for channel 3   from your receiver.  Combine satellite receiver with off air for clean picture.

$19.99

DiSEqC switches, 1x2 and 1x4

1x4  $7.99

 2x1 DiSEqC switches , $1.99 each or 10 for $17.99.  Model GD-211 closeout, no return. 

Switches may come from different manufacturers and differ from picture at left.

Add $2 for waterproof switch in cover

Invacom SNH-031 Universal Single LNBF  Specs

$44.95  available ONLY A FEW OF THESE GREAT 

lnbf'S Available, 



 
Invacom QDH-031 Universal Quad LNBF  Specs

$109.95  out of stock



Invacom SNF-031 Universal

$58.95 out of stock - 

 


Invacom QPF-031 Quad Polar (CP/LP).  CallCircular+Linear lnb to be used with ADF-120 for prime focus dish $96.95 .

 

 
Invacom QPH-031 Quad Polar LNBF (CP/LP)  Specs
Does DSS and FTA at the same time!!!  

    $69.00    



Invacom ADF-120 Feed horn for Ku Feed Horns

adjustable Prime Focus    $29.95 Specs

out of stock, may not be able to get more


 

I

 

 

 

F Series Invacoms are out of stock, QDF etc. No more available in the USA that we know of. Should they become available I will post a notice at the beginning of our web site.

 

The Invacom importer for USA has not been able to get product for some time thus I  do not know when or if we will be able to get product in the future.  We only have 2 models available, the SNH 031  and the QPH 031.  Sorry NO lnbs for prime focus.

We also have the DSS 922 for $23.99.  This looks like a standard DSS lnbf except that it goes for 11.7 through 12.7 and does circular and linear,  LO 10750  See picture above.  

 

 

 

Invacom SNH-031 Universal Single LNBF  $44.95  just in, special intro price

 

INVACOM  

0.3 db, stable  and the list goes on and on

Taylor Enterprises is an authorized dealer / distributor for Invacom,  coming in late May

Some models are FSS and DBS, circular / linear.

Support up to 4 receivers.

 

Stable and typically 0.3 db,  very very sensitive.

 

Stacking switches Switches can be stacked, that is used together.  Up to 16 different inputs can go to one receiver  MORE INFORMATION ON SWITCHES
Channel Master  Channel King MODEL 3650A UHF/VHF/FM off air antennas, Good fringe antenna just in time for Hi Def. TV  $69.  Must pick up at Cincinnati warehouse.  We have a few left. Pictured on left.  NEW IN BOX  Can not ship, must be picked up at Cincinnati warehouse.
0 / 12 volt switch with two splitters and wiring already made up up.  Use to add one of our receivers to your present big dish C KU setup.  Includes wires and directions  $call
SF - 95,  the good meter, for peaking dishes, MPEG2fta, Analog, Digital, 4DTV, Dish, DirecTV, signal and tone $14.99

 

Its a kit, SF 95 Satfinder with power port, Compass, wire that allows user to power with batteries, designer case, short coax to connect meter to lnbf.  $21.95, this is a no brainer.
Flatwire, run coax under window, around doors, great where you can't drill holes   $4.99   
Polorizer Motor  for big dish feed, Chaparral etc. Servo Motor for Feedhorn on big dish, 2 buttons fits Chaparral and other brands  $22.99
Diplexer, looks like splitter, combine off air antenna with satellite on one cable.  $3.99

various brands

AF1 Satellite Locater 

Professional Site Survey and Satellite Alignment Tool $99

  • Built for fast site surveys and easy installs. 
  • Can be used with one hand.
  • Separate eyepieces for the compass and clinometer.
  • Hairline accuracy.
  • Cost effective.
  • Saves time.
  • Simple operation.
  • Easy to use.
  • Jeweled movements.
  • All moving parts are immersed in dampening liquid.
  • Liquid and moving parts are hermetically sealed inside high strength plastic containers.
  • Liquid dampening prevents vibrations and promotes smooth movements.
  • Compass has a permanent antistatic treatment.
  • Works on Ku, Ka, C, DSS, FSS.
Closeout,  Universal remote control kit!  Replaces many C Band satellite dish remotes,,, IR and UHF,  it can even turn a system with an IR remote into a UHF remote.  You can now shoot your remote through a wall closeout   $25
Remote control for most current MPEG2-fta receivers.$18.99 ( Zinwell ZDX--- $19.99) Other fta models available

 

Hotlinker remote control extender.  $22.99

All prices plus Shipping and Handling    IMPORTANT, pictures are for illustration only,  brands an specifications may vary.  This is especially true in switches, diplexers, splitters etc..

Go to our home page for tons of information

Go to our surplus page for lots more products.   Remote controls to Jeeps, they are all there on our surplus page.

All Items subject to availability. Some items may incur shipping charges even if picked up.   Minimum 20% restocking, no return after 30 days.  No return on items from surplus page.  No return on dishes. See Home and other pages for more details. we attempt to bring you the best product at the best price therefore pictures of items are provided as example of item only,  the item you receiver may very from one in picture.  Manufacturers may vary.  

Order at 859/356-9666 we want to talk to you.